Close

PPR PIPES & FITTINGS

ultimate
Solutions for Complex Applications

An Eco-friendly & Food Grade
PPR-Plumbing System
for Industrial & Commercial segment
for Hot & Cold water applications

ADVANTAGES

PUREFIT PPR-C PIPING SYSTEM

Purefit pipes and fitting are made from Polypropylene Random Co polymer, its suitable for both Industrial and Commercial applications with outstanding reliability over time.


One special feature of the Purefit PPR-C piping system is the assembly technique, in which the parts to be connected are welded by melting and fusion. After fusion welding, the pipe and fittings form a single continuous boy with none of the problems, which may derive from potential leakage points. This makes the joint as PERMANENT. No sealants or adhesives are required for these permanent connections.

SPECIAL FEATURES OF PUREFIT PPR-C PIPING SYSTEM

  • Anti Corrosive & Chemical Resistant

    Chemically inert and highly resistant to wide range of acid bases. Suitable for highly corrosive areas and industrial cooling water, drinking water system.

  • Withstanding High Pressure

    Pipes and fittings can withstand up to 20 kg/sqcm pressure. Suitable for high pressure application like Compressed Air Lines.

  • Low Pressure Drop

    Because of the very smooth non porous inner surface of pipes and fittings the pressure loss is less than metallic pipes, which results saving of pumping energy considerably.

  • Withstanding Higher Temperature

    — Can withstand upto 95°C. Best pipe for solar water transport.

  • Hygienic Harmlessness — Purefit PPR-C

    pipes are certified as food grade pipes as per DIN 1998 T2. Best piping system for drinking water, RO plants and DM Plants.

  • Low Thermal Conductivity

    The material's high level of thermal insulation guarantees low heat loss on the part of fluid transport. (0.24 W/mK)

  • Low Noise

    — Having high sound insulation value, results lower noise level at the time of high speed flws.

  • Non Toxic - Recyclable

    — Unlike PVC pipes, Purefit PPR-C pipes are non toxic at the time of fire and approved by Green Piece. PPR-C is recyclable material.

  • High Impact Rate

    Purefit PPR-C pipes are having high impact strength compare to any plastic pipe.

  • Low Flammability

    Purefit PPR-C pipes and fittings comply with fire classification B2 (normal inflammable) In case of fire no toxic emission to atmosphere like PVC pipes.

  • Resistant to stray electrical current

    Thanks to high electrical insulating properties, Purefit PPR-C pipe system is unaffected by stray currents

  • Like SS Pipe

    The characters of Purefit PPR-C piping system is almost like SS. Purefit PPR-C pipes will have more advantage than SS for the specific application requirements.

PUREFIT PPR-C PIPING SYSTEM

FUSION TECHNIQUE

The process of joining PPR-C pipes and fittings is very simple and results and inseparable watertight joints. It is carried out using a simple welding machine that fuses the internal surface of the fitting and the external surface of the pipe, so that the material of the pipe and the fitting will be bonded together. Prepare the welding machine by fitting it with the welding dies of the diameters to be welded. Connect the plug to the 220V power supply socket and wait until the green light on the machine goes out indicating the welding machine has reached the working temperature.

  • Cut the pipe at right angles to the pipe axis using suitable pipe cutter.

  • Remove any burrs or cutting chips by deburring the cutting area.

  • Mark the welding depth on the pipe using suitable marker.

  • Insert the end of the pipe without turning into the heating sleeve up to the marked welding depth and at the same time slide the fitting without turning into the other side of the heating tool up to the stop. It is essential to observe the mentioned heating times (refer to the below table)

  • Leave the pipe and fitting into the heating tool until the heating time is elapsed.

  • At the end of the heating time, remove the pipe and fitting from the heating tool and push them immediately against each other up to the mark indicating the welding depth. At this stage the depth mark will be covered with the welding bead.

  • During this process, do not rotate the pipe and fitting relative to each other.

  • During this process, do not rotate the pipe and fitting relative to each other.

  • Allow the joint to cool fully before using.

Member

EEPCINDIA

CII

FIEO